Exploring microsilica’s role in ultra-high-strength ‎‎‎concrete: An ‎experimental study

Exploring microsilica’s role in ultra-high-strength ‎‎‎concrete: An ‎experimental study

Amirhossein Arman1 Ayda Kazemi Motlagh2 Erfan Shafei3 Ehsan Kuse sedan4 Tadeh Zirakian5 Mohammad reza Saei6

1) B.Sc., Department of Civil Engineering, Urmia University of Technology (UUT)‎, Iran.‎
2) B.Sc. Student, Department of Civil Engineering, UUT‎, Iran.‎
3) Associate Professor‎, Department of Civil Engineering, UUT Urmia, Iran.‎
4) M.Sc. Student, Department of Structural Engineering, Amirkabir University of Technology‎, ‎Tehran, Iran.‎
5) Associate Professor, Department of Civil Engineering and Construction Management‎, ‎California State University‎, ‎Northridge‎, USA.‎
6) ‎Instructor‎, Concrete Lab, Department of Civil Engineering, UUT‎, Iran.

IOI Code : AACC-AAHAKA
Publication : Third International Conference on applied researches in civil engineering, architecture and urban planning (icarcau.com/3rd)
Abstract :
    The production of cement significantly contributes to global CO₂ emissions. ‎Therefore, it is essential to ‎‎identify alternative supplementary cementitious materials ‎‎(SCMs), such as fly ash, micro silica, and slag, ‎‎that enhance concrete performance ‎while reducing environmental impact. Among these, micro silica (MS) ‎‎is considered ‎one of the most effective SCMs. It is an ultrafine amorphous silica produced as a ‎‎byproduct ‎of electric arc furnace processes during the production of silicon or ‎ferrosilicon alloys. Due to its high ‎‎pozzolanic reactivity and microfiller effect, MS ‎contributes to matrix densification and reduced porosity, ‎‎thereby enhancing the ‎strength and durability of concrete. This study investigated the effect of MS on ‎the ‎‎mechanical behavior of ultra-high-strength concrete (UHSC). Basalt aggregates are ‎suitable for use ‎due to ‎their high strength, low reactivity, and excellent durability. ‎For this purpose, based on both ‎technical and ‎economic considerations, a 65: 35 ‎coarse and fine aggregate mixture was selected. To this ‎end, 24 cubic ‎specimens (100 ‎mm) were prepared using four mix designs containing 0 (control ‎scheme), 5, 10, and ‎‎15% ‎MS by weight of cement. All mixes had a constant water-to-cement ratio (W/C) ‎of ‎‎0. 0.2 and identical ‎basalt aggregate grading. Compressive strength tests were ‎conducted at curing ages of 7, ‎‎14, and 28 days. ‎Specimens were prepared under ‎standardized conditions and cured in a saturated lime-water tank at a ‎‎controlled ‎temperature of 23 ± 1 °C until testing‎. The present study s findings showed ‎that the ‎highest ‎compressive strength, recorded at 133 MPa, was achieved at 28 days for the ‎specimen ‎containing 15% MS, ‎representing a 25% increase compared to the control ‎scheme. The observed increase ‎in ‎compressive ‎strength is attributed to the ‎pozzolanic reactions of MS, which reduce total porosity, limit ‎pore ‎connectivity, and ‎promote matrix densification in the concrete microstructure.‎

Keywords : ultra high strength concrete (uhcs) supplementary ‎cementitious materials ‎‎(scms) microsilica content superplasticizer pozzolanic materials basalt‎