نمایش چکیده فارسی

Stress Intensity Factor for Cracked Sheets with Broken Hole Using CFRP

ali haghi navand1 motahare sadat razian2 hamid khafajeh3

Abstract :
The use of stopper holes is one of the easiest methods to reduce the stress intensity factor at the tip of the crack and thus reduce the growth rate of the crack. The effectiveness of stopping holes in inhibiting crack growth is considered based on their effect on stress intensity coefficients. The numerical results indicate that the position and size of the stopping holes influences the amount of crack stress intensity coefficient. By increasing the size of the holes on both sides of the crack and decreasing their horizontal and vertical distances from the crack tip, the intensity of the stress intensity is also increased. However, fatigue cracks usually occur in places where excavation of the cavity in required dimensions due to geometric constraints is not feasible. In such a situation, crack may start again from the hole. Hence, there is a need to reinforce broken holes. In the present study, a combination of cracked cavities and carbon-fiber reinforced polymers (CFRP) under static loads was studied using finite element analysis (FEA) to evaluate its potential as a modification technique. The steel plate with the primary center crack under static tensile loading (Mode I) was considered. The holes of both sides of the cracks were molded and CFRP pieces were applied on each side of the cracks. ANSYS software used in order to perform numerical analysis.

Keywords : ansys cfrp hole stress crack


زبان مقاله : انگلیسی
محور مقاله : علوم مهندسی
محل انتشار : دومین کنگره بین المللی علوم، مهندسی و تکنولوژی - هامبورگ
آدرس وب سایت کنفرانس : germanconf.com/2nd
کد IOI مقاله : XACC-CAZKF
لینک مستقیم مقاله : https://isnac.ir/XACC-CAZKF
نمایش چکیده فارسی : https://isnac.ir/SA/XACC-CAZKF

سایر مقالات محل انتشار
  1. Forecasting Annual Extreme Flows Rate of Karkheh River using Stochastic Models
  2. بررسي استرس هاي دما در فرآيند كشت سلولي توليد اريتروپويتين نوتركيب
  3. بررسی اثر سطح پروتئین و ليزين جیره برکمیت و کیفیت توليد مرغهای تخمگذار در سن 28 تا 42 هفتگی
  4. Improvement of properties of polyaniline by changing the reaction conditions
  5. بررسی میزان آلایندگی آب و رسوب کف تالاب انزلی نسبت به عنصر کادمیم و پالایش آن توسط گیاه آبزی آزولا (Azolla pinnata)
  6. Deep Learning for Bleeding Detection in Endoscopic Capsule Images
  7. مبانی دزیمتری ترمولومینسانس برای پرتوهای نوترون
  8. Study on Tissue Culture, Callus Induction and Micropropagation of Rosemary (Rosemary officinalis)
  9. تدوین استراتژی بازار یابی انرژی الکتریکی مورد نیاز صنایع در منطقه ویژه اقتصادی انرژی پارس
  10. ارزيابي تاثیر افزودن آهك بر روي پارامترهاي مقاومت برشي خاك هاي ماسه اي و ماسه اي رس دار
  11. پخش بار بهینه سیستم قدرت با هدف کاهش هزینه سوخت با استفاده از الگوریتم های کرم شب تاب و کلونی زنبور عسل
  12. بررسی شهادت و لزوم حمایت از شاهد
  13. بررسی کمیت و کیفیت پسماند مطب های دندانپزشکی شهر سبزوار در سال ۱۳۹۴
  14. تحلیل تنش در سیلندر کامپوزیتی دوار تقویت شده با نانولوله های کربنی تحت میدان های مغناطیسی و مکانیکی
  15. تحلیل تنش در سیلندر کامپوزیتی دوار تقویت شده با نانولوله های کربنی تحت میدان های مغناطیسی