نمایش چکیده فارسی

Comparison of Experimental Tests and Finite Element Analysis of Steel Pipe Roller Bending Process (St37 and ALFORM)

Behnam Sadeghi Najafabadi1

Abstract :
Pipe bending is widely used in aerospace, automotive and other industries. Wrinkling of thin-walled pipes, deformation of the cross-section and changes in thickness during pipe bending are the main problems of this process. Compressive force and internal pressure can be used to better control the bending process. If the ratio of bend radius to pipe diameter (R/D) in the bending process is between 1 and 1.5, bending cannot be done with usual methods. It is important to present a new method that can remove the wrinkles in the pipe and minimize the thickness changes in its wall. In this research, a new method for press bending of high strength steel sheets has been investigated. The amount of spring return is one of the main parameters that have been investigated in this research using the finite element method and the experimental method. For this purpose, a cylinder with a diameter of 100 mm made of ALFORM material has been formed in three steps using a steel mold specially made for this process. Then the same process is simulated with ABAQUS software. In another step of this article, ST37 structural steel was used and examined, and the research process was repeated and its results were compared and examined. As expected, spring rebound in high strength steel was much higher than structural steel. From the analysis of the practical and finite element results, it was concluded that the spring return rate of ALFORM in this method is about 5% of the diameter and this number is equal to 1% in ST37 steel. In addition, it was found that the parameter of the place of placing the sheet on the mold and the distance from the edge of the sheet to the center of the matrix is one of the issues that in the results extracted in the research, including the distance between the two edges of the part from each other after the end of the first and second steps, they reached the shape Uniform circular geometry is very effective at the end of the third stage.

Keywords : experimental test spring back finite element abaqus alform st37


زبان مقاله : انگلیسی
محور مقاله : مهندسی مکانیک
محل انتشار : هفتمین کنفرانس بین المللی پژوهش های کاربردی در علوم و مهندسی
آدرس وب سایت کنفرانس : 7carse.com
کد IOI مقاله : XGZK-HKKKB
لینک مستقیم مقاله : https://isnac.ir/XGZK-HKKKB
نمایش چکیده فارسی : https://isnac.ir/SA/XGZK-HKKKB

سایر مقالات ارائه دهنده
  1. Simulation, Analysis and Investigation of Crack Behind the Timing Belt of Pride and XU7 With XFEM technique Using Finite Element of ABAQUS software
  2. Simulation, Analysis and Investigation of Shear Walls of Reinforced Concrete Under Seismic Load With ABAQUS Software Using Finite Elements Method
  3. Simulation and Analysis of Cracks Growth Mechanism and Propagation in Steel Shear Wall
  4. Evaluation of Compatibility of Architectural Model and Physical Planning of Iranian Cities with Features of Iranian - Islamic Architecture
  5. Numerical Analysis and Simulation Concrete Water Tanks Under Seismic Load Using ABAQUS Finite Element
  6. Finite Element Analysis of Steel Shear Wall Reinforced With CFRP Composite
  7. Simulation of Progressive Destruction In Concrete Buildings By Using Finite Element Of ABAQUS
  8. The Effect of Unbalanced Magnetron Spattering on Mechanical Properties and Strength of Titanium Nitrate and Tin Dioxide Thin Films
  9. Simulation and Analysis of Cylindrical and Spherical Pressure Vessel
  10. Simulation of Three-Roller Pipe Bending Process Using ABAQUS Finite Element Method
  11. Analysis of In-Cylinder Fluid Based on Navier-Stokes Equations
  12. Analysis Based on Newton-Raphson Equations and Compare With Results of ANSYS Software in Hydraulic Cylinder
  13. Evaluation of Fatigue Phenomenon Effect in Polyvinyl Chloride Pipes Under Reversible Cyclic Loads
  14. Measuring the Rate of Carbon Dioxide Production Due to the Effect of Humidity on the Optical Degradation of Polyvinyl Chloride and Polyethylene
  15. The Effect of Additive Elements on Surface of Polyvinyl Chloride and investigation of its Floatability properties
سایر مقالات محل انتشار
  1. Examining sexual organ cancers and changes in sexual function in women with cancer
  2. ارائه يك سيستم كنترلي مناسب در یک شبکه دو ناحیه¬ای و طراحی کنترل کننده با استفاده از بهینه¬سازی کنترل¬کننده فازی با الگوریتم هوشمند PS
  3. دنیای مهندسی هسته ای و نسل های مختلف انرژی خورشیدی
  4. بررسی ریسک های رایانش ابری در صنعت بانکداری
  5. رابطه جبر خطی و هوش مصنوعی
  6. استفاده از سدیم هگزامتافسفات در ازدیاد برداشت نفت و بررسی آثار آن
  7. مفهوم سکونت در معماری سنتی ایران
  8. Reactive Cyber threat intelligence in financial systems
  9. حل معادله جابجایی- نفوذ برای محاسبه توزیع دما در جریان دوبعدی دائم با فرض میدان سرعت معلوم در هندسه نشان داده شده با شرایط مرزی معین شده
  10. مقایسه تطبیقی اصول سبک فولدینگ و دیکانستراکشن بر آثارپیتر آیزنمن و بهرام شیردل
  11. بهبود ظرفیت باربری ستون های صلیبی شکل فولادی با استفاده از لینک های الصاقی
  12. A New High Step-Up DC-DC Converter Based on Voltage Multiplier Cell and Coupled Inductor
  13. Effect of Si3N4 nanoparticles on microhardness and corrosion resistance of Ni-Co electrodeposits
  14. Investigation of PRO processes and the possibility of energy production from the natural process of osmosis
  15. انواع مالت و بررسی دوام مالت های حاوی پوزوالن طبیعی