جستجو
Numerical Modeling and Optimization of Superheater with Genetic Algorithm
Masoomeh Shadab1 Neda Dorostkar2 Soheil Pazoki3
Abstract :
Superheaters tubes are constantly exposed to fouling. Therefore, studying the superheaters by consideration of the covered scale layer inside pipes and sediment layer on it and its effect on the output superheated steam temperature and the amount of injected water into the output superheated steam has special impact. In this research, for 3-D analysis of the heat transfer parameters and flow field characteristics, a commercial mechanical software (ANSYS-CFX 19) is employed. Finally, the calculated average output superheated steam temperature from the superheater has been compared with experimental data. In this way the accuracy of this simulation is valid. subsequently, two-objective optimization is done by Genetic Algorithms. The pressure and temperature of the injected water are considered for the design variable of this optimization. amount reduction of water spray and increasing of the superheater’s efficiency coefficient are considered as objective functions. Finally, the optimization results are analyzed.
Keywords : superheater fouling spray water optimization genetic algorithm
زبان مقاله : انگلیسی
محور مقاله : گروه مکانیک
محل انتشار : دومین کنفرانس مکانیک،مهندسی برق و کامپیوتر ایتالیا
آدرس وب سایت کنفرانس : mecconf.com/2nd
کد IOI مقاله : XCBC-EECZH
لینک مستقیم مقاله : https://isnac.ir/XCBC-EECZH
نمایش چکیده فارسی
: https://isnac.ir/SA/XCBC-EECZH
سایر مقالات ارائه دهنده
- Numerical Modeling and Optimization of Superheater with Genetic Algorithm
- Computational and experimental investigation of thermal behaviour and flow field of a mechanical seal
- Simulation of the thermal Characteristics and laminar flow field around the mechanical seal rings
- The effect of impeller blades number on the performance of a centrifugal pump with complete and trimmed impeller
- Dissolution of the Boundary Layer of Micropolar Fluid with Nanoparticle (Go) in the Engine Oil Fluid in a Porous Medium on the Elastic Plate Affected by MHD Considering the Joule Heating Force by AGM Method
- Pumps; Series or Parallel; a Review of a Common Misconception
- بررسی عملکرد ایندیوسر پمپ سانتریفیوژ در شرایط کاویتاسیون و ملاحظات طراحی هیدرولیکی و هندسی آن
سایر مقالات محل انتشار
- طراحی و شبیه سازی انتن نیم دایره ی دوبل در محدوده ی فرکانسی 5 تا 15 گیگاهرتز
- بررسی هوش مصنوعی در بهداشت و درمان
- طراحی کنترل کننده تحمل پذیر عیب عملگر در سیستم کوادروتور در حالت شناور
- جایابی چند منظوره بهینه ی پست های توزیع با در نظر گرفتن قابلیت اطمینان با استفاده از الگوریتم جستجوی موجودات همزیست (SOS)
- بهينهسازي مصرف انرژي در شبكههاي حسگر بی سیم برمبناي الگوريتمهاي مسيريابي با استفاده از اتوماتاي يادگير سلولي
- ارائه یک مدل تصمیمگیری شناختی بر اساس عامل (SOAR)
- تشخیص و جداسازی عیبهای چند عملگر با استفاده از فیلترکالمن توسعه یافته در سیستم کوادروتور در حالت شناور در یک نقطه
- Active Fault Tolerant Control for a Multi-Actuator fault of Quadrotor System in Hovering Mode
- مدلسازی و تحلیل عددی جریان اطراف ایرفویل متقارن NACA0012 تحت زوایای حمله مختلف با استفاده از روش مدلسازی K.ω SST
- ارائه راهکارهای مبتنی بر مسیریابی ccrبمنظورکاهش تاخیر درحمل ونقل شهری دربستراینترنت اشیا
- بررسی تاثیر امواج الکترومغناطیس تلفن همراه بر روی چشم انسان
- معضل ناامنی اینترنت اشیاء در دستگاههای IOT
- Numerical Modeling and Optimization of Superheater with Genetic Algorithm
- کنترل بهینه ی ربات های صنعتی مبتنی بر رویتگر با استفاده از الگوریتم رقابت استعماری
- تشخیص پوسیدگی دندان با استفاده از یادگیری ماشین