جستجو
Numerical Investigation, Prediction and Comparison of Ductile, Shear and MSFLD Damage Model in Cross-Shape Tube Hydro-Forming Process
Hamidreza Alinaghian Elyaderani1 Hossein Ghazavi2
Abstract :
The tube hydro-forming process consists of the simultaneous or sequenced application of an axial compression as well as an internal pressure (transmitted by a fluid medium, e.g. water) into a cavity or hollow part in order to produce tubular parts with different transversal sections. It s a manufacture process used mainly for the automobile and aeronautical industries for the manufacturing of low-cost parts, with reduced weight and bigger structural integrity when compared with conventional metal forming processes. Currently two techniques of hydro-forming are distinguished: the hydro-forming with sequenced pressurization, PSH (pressure sequence hydro-forming) and the hydro-forming under high pressure, HPH (high-pressure hydro-forming). Both the techniques had been developed to facilitate the forming process of more complex parts preventing problems of wrinkling, buckling and rupture. A three-dimensional finite element simulation, based on the rigid–plastic model for the analysis and design of hydro-forming process was developed. The hydraulic pressure force is applied to the normal direction of the tube work piece by integrating the pressure with respect to each element’s surface area. The predicted simulation results provide information on the actual design. This numerical approach to the hydro-forming process will be useful to the development and application for a wide range of automobile structural components. In this paper, 3D models of hydro-forming has been simulated by finite element method. Three damage model, coupled with von Mises plastic criterion, have been applied to predict where and when onset of ductile, shear and MSFLD rupture occur. Also, 3D models of hydro-forming has been simulated to study the deformation of blank, distribution of stress contours and contour of equivalent plastic strain in process. All studies presented in this paper have been carried out on aluminum alloy EN AW-7108 T6.
Keywords : hydro forming numerical investigation cross shape tube ductile fracture criteria shear fracture criteria msfld fracture criteria aluminum alloy en aw 7108 t6
زبان مقاله : انگلیسی
محور مقاله : مهندسی مکانیک
محل انتشار : اولین کنگره بین المللی علوم، مهندسی و فن آوری های نو
آدرس وب سایت کنفرانس : secongress.com/1st
کد IOI مقاله : XEHE-HCFBB
لینک مستقیم مقاله : https://isnac.ir/XEHE-HCFBB
نمایش چکیده فارسی
: https://isnac.ir/SA/XEHE-HCFBB
سایر مقالات محل انتشار
- اثرات طراحی سبز در طرح توسعه مجموعه آموزشی - دانشگاهی با رویکرد مدیریت سبز
- بررسی توان های محیطی در ارتقا خدمات گردشگری کشورهای پسانفتی با تاکید بر پایداری اقتصادی (نمونه موردی: جزیره هندورابی)
- Simulation, Analysis and Evaluation of Fracture Mechanics of Aluminum Sheet Forming Process with Rubber Substrate
- Simulation and Analysis of the Cutting and Drilling Process of the Human Skull Bone with Water Jet Process Using Finite Element ABAQUS Software.
- Simulation of Impact hard object on Knee Joint and Investigation of stress on it Using Finite Element Method
- Numerical Investigation, Prediction and Comparison of Ductile, Shear and MSFLD Damage Model in Cross-Shape Tube Hydro-Forming Process
- Simulation and Evolution of a New Seismic Flexural Connection System for Steel Structures
- Investigating the Effect of Cuo nano-particles on the Hydrodynamic Properties of the Non-Newtonian Fluid (water + CMC) Inside the Tube, With the Boundary Condition of Uniform Velocity at the Inlet Section and Under Constant Thermal Flux in the Laminar Flow Range
- Preparation of Silicon Carbide Refractory Coating by Chemical Vapor Deposition Using Hexamethyldisilylamine Precursor.
- Presentation of Proposed Model for Zero Carbon Buildings Based on Commercial Models
- Evaluation of Fatigue Phenomenon Effect in Polyvinyl Chloride Pipes Under Reversible Cyclic Loads
- Measuring the Rate of Carbon Dioxide Production Due to the Effect of Humidity on the Optical Degradation of Polyvinyl Chloride and Polyethylene
- The Effect of Additive Elements on Surface of Polyvinyl Chloride and investigation of its Floatability properties
- Evaluation of the Effect of Zn3(C3N3O3)2. ZnO as a Thermal Stabilizer on Polyvinyl Chloride
- Investigation of Mechanical and Thermal Properties of Flexible PVC-EBSO